View unanswered posts | View active topics It is currently Thu Aug 05, 2021 8:22 am



Reply to topic  [ 5 posts ] 
Courier bumperettes ... Needed ? ... UPDATE 
Author Message

Joined: Wed Feb 03, 2010 7:52 am
Posts: 1012
Reply with quote
Post Courier bumperettes ... Needed ? ... UPDATE
Some years ago ERCL had a small batch of the Mk.1/2/3 Courier bumperettes produced in the original form, aluminium alloy, and when polished they looked fabulous. Later cars had the same parts in painted grp and there was talk about having molds produced to replicate the grp version ... did anyone take that forward??


Wed Oct 21, 2020 7:13 am
Profile

Joined: Wed Aug 29, 2012 12:06 pm
Posts: 13
Location: Absecon, NJ USA
Reply with quote
Post Re: Courier bumperettes ... Needed ???
Rodger, I am presently attempting to produce grp bumperettes. I have put together molds but am having trouble with releasing them from the molds. Am delayed just now but will keep all advised of my progress. So far I have a test pair of front end bumpers but they are a little rough and I was forced to destroy the mold to free them.
Joe Marchione


Thu Oct 22, 2020 9:40 pm
Profile

Joined: Sun Jun 26, 2011 3:31 am
Posts: 13
Reply with quote
Post Re: Courier bumperettes ... Needed ???
Joe, just saw this thread... had a thought or 2 to share...

Don't know how you did the mold, but believe you should make each 2 part, with flanged/split down center of them.... If like me, you probably tried to do in a single piece, which likely locked the part in once made. So, if needing to redo molds, look at split on peak.

If a matter of mold release, then you should wax extremely well, then brush or lightly dust in PBA or PBB mold release. These are water soluable release agents (alcohol based), available form most fiberglass places. I always had an issue with surface finish having brush strokes (fisheyes when sprayed...to heavy likely). but will definitely make releasing easier.

Finally, you might consider adding a couple of ports on back side of mold, you can put air pressure or water in from those to push part off the mold. Typically, a 1/4" coupling glued to back side with hole thru mold, then put a piece of tape over the hole on mold inside...(clear packing tape works well) to close if off ....will have a small spot on part where tape was, but really makes stuff pop out easier.

Wish you luck...a worthwhile project....for someone else!

Bob L.


Thu Oct 29, 2020 12:42 am
Profile

Joined: Wed Feb 03, 2010 7:52 am
Posts: 1012
Reply with quote
Post Re: Courier bumperettes ... Needed ???
There still appears to be people who would be pleased to acquire a set of bumperettes for the Mk.1-3 Couriers .. did anyone make any progress with the project to reproduce these? It can be done as ELVA Racing supplied in polished aluminium alloy c.15 years ago ..... they looked great in situ!!


Tue Jan 19, 2021 10:27 am
Profile

Joined: Mon Jul 20, 2020 12:20 am
Posts: 1
Location: Fort Wayne, IN
Reply with quote
Post Re: Courier bumperettes ... Needed ? ... UPDATE
If the bumperettes do make it back into production, please count me in for a front and rear set. Also, I am looking for an Elva Courier front badge and steering wheel boss for my Mark III.

Thanks!

Greg Perigo


Tue Jul 13, 2021 3:08 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 5 posts ] 

Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

Protected by Anti-Spam ACP Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware.